Engel e-victory 50/50 (2019) ecodriveEngel
e-victory 50/50
Engel e-victory 50/50 (2019) ecodrive
Engel
e-victory 50/50
Năm sản xuất
2019
Tình trạng
Đã qua sử dụng
Vị trí
Trenčianske Stankovce 

Dữ liệu cơ bản
- Nhà sản xuất:
- Engel
- Mô hình:
- e-victory 50/50
- Năm sản xuất:
- 2019
- Tình trạng:
- gần như mới (đã qua sử dụng)
Giá & Vị trí
- Vị trí người bán:
- 3011 Sedličná, 913 11 Trenčianske Stankovce, Slovakia

Gọi điện
Chi tiết kỹ thuật
Tài liệu và chứng nhận
Tài liệu / sổ tay hướng dẫn
Thông tin chi tiết
Lực kẹp:
500 kN
Chi tiết về đề nghị
- ID tin đăng:
- A22892835
- Số tham chiếu:
- 260289
- Cập nhật:
- lần cuối vào ngày 16.11.2026
Mô tả
_ENGEL – Injection Moulding Machine Technical Data_
Serial number: 232665
Model: E‑VICTORY
Kedpfsz Iyldox Adhjdw
_Plasticising Unit 1_
• Screw diameter: 18 mm
• Listed diameter options: 15 / 18 / 20 mm; 18 mm is installed
• Screw stroke: 80 mm
• Maximum injection volume: 20 cm³
• Screw speed: 450 rpm
• Screw torque: 75 Nm
• Plasticising rate, 3-zone screw: 4.2 g/s
_Injection Unit 1_
• Version: Standard
• Injection rate: 83.97 cm³/s
• Specific injection pressure, regenerative mode: 2,400 bar
_Nozzle 1_
• Nozzle stroke: 210 mm
• Nozzle contact force: 40.6 kN
_Material Cylinder 1_
• Screw L/D ratio: 24
• Heating zones, including nozzle: 4
• Heating power: 5.1 kW
• Note: maximum available equipment
_Clamping Unit_
• Clamping force: 500 kN (approximately 50 tonnes)
• Opening stroke + cylinder tolerance: 408 mm
• Maximum distance between platens: 600 mm
• Minimum mould height: 200 mm
• Platen dimensions, horizontal × vertical: 500 × 450 mm
• Drop-out chute width: 400 mm
• Maximum mould weight on moving platen: 300 kg
• Maximum mould weight on stationary platen: 300 kg
• Maximum total mould weight: 600 kg
• Dry-cycle stroke according to Euromap 6: 150 mm
• Dry-cycle time according to Euromap 6: 1.60 s
Mould weight notes:
1. Mould overhang according to mounting platens.
2. Less the weight of any rotary table.
_Ejector 1_
• Ejector stroke: 100 mm
• Ejector force: 39.8 kN
_Drive Unit_
• Oil reservoir capacity – injection unit, main tank: 135 l
• Oil reservoir capacity – clamping unit, auxiliary tank: 0 l
_Machine Basics_
• Total weight without oil: 4.0 tonnes
• Total connected power: 65.0 kW
Transcription note: the small footnotes below the plasticising section specify
reference materials and test conditions. They are not fully legible in this
photo.
Serial number: 232665
Model: E‑VICTORY
Kedpfsz Iyldox Adhjdw
_Plasticising Unit 1_
• Screw diameter: 18 mm
• Listed diameter options: 15 / 18 / 20 mm; 18 mm is installed
• Screw stroke: 80 mm
• Maximum injection volume: 20 cm³
• Screw speed: 450 rpm
• Screw torque: 75 Nm
• Plasticising rate, 3-zone screw: 4.2 g/s
_Injection Unit 1_
• Version: Standard
• Injection rate: 83.97 cm³/s
• Specific injection pressure, regenerative mode: 2,400 bar
_Nozzle 1_
• Nozzle stroke: 210 mm
• Nozzle contact force: 40.6 kN
_Material Cylinder 1_
• Screw L/D ratio: 24
• Heating zones, including nozzle: 4
• Heating power: 5.1 kW
• Note: maximum available equipment
_Clamping Unit_
• Clamping force: 500 kN (approximately 50 tonnes)
• Opening stroke + cylinder tolerance: 408 mm
• Maximum distance between platens: 600 mm
• Minimum mould height: 200 mm
• Platen dimensions, horizontal × vertical: 500 × 450 mm
• Drop-out chute width: 400 mm
• Maximum mould weight on moving platen: 300 kg
• Maximum mould weight on stationary platen: 300 kg
• Maximum total mould weight: 600 kg
• Dry-cycle stroke according to Euromap 6: 150 mm
• Dry-cycle time according to Euromap 6: 1.60 s
Mould weight notes:
1. Mould overhang according to mounting platens.
2. Less the weight of any rotary table.
_Ejector 1_
• Ejector stroke: 100 mm
• Ejector force: 39.8 kN
_Drive Unit_
• Oil reservoir capacity – injection unit, main tank: 135 l
• Oil reservoir capacity – clamping unit, auxiliary tank: 0 l
_Machine Basics_
• Total weight without oil: 4.0 tonnes
• Total connected power: 65.0 kW
Transcription note: the small footnotes below the plasticising section specify
reference materials and test conditions. They are not fully legible in this
photo.
Những tin rao vặt này cũng có thể bạn quan tâm.
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Trenčianske Stankovce
8.866 km
Engel E-VICTORY 170H/50V/120 Kombi (2015) Ecodrive, VIPER 20 ROBOT TUYẾN TÍNH
EngelE-Victory 170H/50V/120 combi
EngelE-Victory 170H/50V/120 combi
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Juszczyn
8.728 km
Thợ đúc
WeinigProfimat 23 Fortec
WeinigProfimat 23 Fortec
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Rumani
9.576 km
Engel DUO 7050/650 pico
EngelDUO 7050/650 pico
EngelDUO 7050/650 pico
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Düngenheim
9.589 km
Pa lăng cáp điện 3.2t, hàng mới có sẵn
Abus KransystemeGM800.3200 H-202.41.6000.4E 100.20
Abus KransystemeGM800.3200 H-202.41.6000.4E 100.20
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Schlüchtern
9.424 km
Công cụ phòng phay máy
HermleUWF 802 M
HermleUWF 802 M
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Eisingen
9.527 km
Máy ép phun
ENGELe-motion 310/160T
ENGELe-motion 310/160T
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Wilków
8.848 km
Máy nén khí trục vít
KaeserASD 47 SFC
KaeserASD 47 SFC
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Sheffield
10.021 km
Máy in 3D
ProJetSD6000
ProJetSD6000
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Burgoberbach
9.384 km
Thiết bị ngoại vi
Wanner TechnikC17.31sv
Wanner TechnikC17.31sv
Thành công
Tin nhắn của bạn đã được gửi đi.
Quảng cáo nhỏ
Скопје
8.716 km
Máy ép phun nhựa
BATTENFELDPLUS 35-INJECTION MOLDING MACHINE
BATTENFELDPLUS 35-INJECTION MOLDING MACHINE
Quảng cáo của bạn đã được xóa thành công
Đã xảy ra lỗi




























































































































































