Máy làm kính cách nhiệtlisec
Inspection Lightwall
Máy làm kính cách nhiệt
lisec
Inspection Lightwall
năm sản xuất
2021
Tình trạng
Đã qua sử dụng
Vị trí
Maasmechelen 

Hình ảnh cho thấy
Hiển thị bản đồ
Thông tin về máy móc
- Tên máy:
- Máy làm kính cách nhiệt
- Nhà sản xuất:
- lisec
- Mô hình:
- Inspection Lightwall
- Năm sản xuất:
- 2021
- Tình trạng:
- rất tốt (đã qua sử dụng)
Giá & Vị trí
- Vị trí:
- Breitwaterstraat 22, 3630 Maasmechelen, Belgique

Gọi điện
Chi tiết về đề nghị
- ID tin đăng:
- A18625526
- Cập nhật:
- lần cuối vào ngày 01.03.2025
Mô tả
1. Switch on the wall and the electronics.
Do this by switching on the mean switch and the lightwall (on the back). So switch on the multimeters. See photos 1 and 2
2. Adjust the upper and lower beam to the right cell height. Do this with 2 people. See photo 3
3. Check if there is no power on the cables coming from the power beam. Use the multimeters for this.
4. Connect the cells with the cables.
5. Check the cells with the protocol “Q3 quality finished cell”.
Iiedsv Ep U Aopfx Ah Hji
6. Use the right voltages for the different products. 24V for ddLC and 46V for scatter.
7. When doing the capacity measurement, turn the black switching knob from “power” to “R/C”. When done turn it back to “power”
8. When you have ddLC cells use the lightwall and the rotatable polar.
9. If you have scatter cells remove the lightwall and use the spotlight. For swtiching on/of this spotlight you can use the remote control. See photo 4.
10. When you are done, please use the mainswitch to power down, and switch of the used lights.
Tin đăng này được dịch tự động. Có thể có lỗi dịch thuật.
Do this by switching on the mean switch and the lightwall (on the back). So switch on the multimeters. See photos 1 and 2
2. Adjust the upper and lower beam to the right cell height. Do this with 2 people. See photo 3
3. Check if there is no power on the cables coming from the power beam. Use the multimeters for this.
4. Connect the cells with the cables.
5. Check the cells with the protocol “Q3 quality finished cell”.
Iiedsv Ep U Aopfx Ah Hji
6. Use the right voltages for the different products. 24V for ddLC and 46V for scatter.
7. When doing the capacity measurement, turn the black switching knob from “power” to “R/C”. When done turn it back to “power”
8. When you have ddLC cells use the lightwall and the rotatable polar.
9. If you have scatter cells remove the lightwall and use the spotlight. For swtiching on/of this spotlight you can use the remote control. See photo 4.
10. When you are done, please use the mainswitch to power down, and switch of the used lights.
Tin đăng này được dịch tự động. Có thể có lỗi dịch thuật.
Nhà cung cấp
Lưu ý: Đăng ký miễn phí hoặc đăng nhập, để truy cập tất cả thông tin.
Đã đăng ký từ: 2019
Gửi yêu cầu
Điện thoại & Fax
+32 89 53... quảng cáo
Quảng cáo của bạn đã được xóa thành công
Đã xảy ra lỗi








